Radar Receiver Outputs
The radar receiver amplifies the weak echo signal and prepares it for subsequent signal processing. Depending on the receiver design, different signal formats may be available at its outputs. A basic distinction can be made between processing the signal amplitude alone and processing that also preserves the phase information of the received signal.
Older radar systems frequently used separate signal paths for these purposes. The amplitude channel provided a simple video signal for displaying echo pulses, while the coherent channel supplied the information required for Doppler processing. Modern radars generally digitize their received signals. Different processing methods can therefore operate on the same digitized signal data.
Amplitude Channel
Figure 1: Simple envelope detector
Figure 1: Simple envelope detector
In the simplest case, the amplified intermediate-frequency signal is rectified by an amplitude demodulator and then filtered. This removes the intermediate-frequency carrier while retaining the time-varying amplitude of the received signal. In radar terminology, the resulting output is called a video signal. This term originated in classical radar technology and does not mean that the signal is a television signal.
The bandwidth of the video signal depends on pulse duration, signal waveform, and the requirements of subsequent processing. It may extend to several megahertz. For this reason, radar engineers do not normally describe it as an audio-frequency signal, as they might in a conventional radio receiver. The basic principle of envelope detection is nevertheless the same as that used to demodulate an amplitude-modulated radio signal.
The video signal contains information about the amplitude of the received echo pulses. The range to a reflecting object can be determined from their time of arrival. Echo amplitude provides an indication of signal strength, but it also depends on range, antenna radiation pattern, target radar cross section, and receiver gain. Therefore, the physical size of a target cannot be determined directly from echo amplitude alone.
An important disadvantage of simple envelope detection is that the phase information of the intermediate-frequency signal is lost. Consequently, coherent Doppler frequency processing can no longer be performed using this video signal alone. In addition to the desired target echoes, interference signals and echoes from stationary objects, commonly referred to as clutter, are also present at the output.
In older analog surveillance radars, the amplitude channel could therefore serve as an additional display path. It displayed echoes that might otherwise have been substantially attenuated by subsequent stationary-target cancellation. This type of presentation was particularly useful in range intervals with relatively little clutter.
Amplitude information remains important in modern radar systems. For example, it can be used
- to assess signal and interference conditions,
- to identify weather echoes and other extended areas of reflectivity,
- to monitor signal levels and receiver operation, and
- for measurement and test purposes within the BITE system.
However, such amplitude information no longer has to be obtained through a separate analog demodulator. It can also be calculated from digitized received signals.
Coherent Channel
Figure 2: Block diagram of a quadrature demodulator
Figure 2: Block diagram of a quadrature demodulator
To detect a Doppler frequency, the phase changes of the received signals over time must be measurable. This requires a sufficiently stable phase reference against which the phase of the received echo can be compared. The intermediate-frequency signal is therefore applied to a phase-sensitive demodulator.
In the widely used quadrature demodulation technique, the intermediate-frequency signal is mixed with two reference signals whose phases differ by 90°. After low-pass filtering, two baseband signals are obtained:
- the I component (in-phase), representing the signal component in phase with the reference, and
- the Q component (quadrature), representing the component shifted by 90° relative to the reference.
Together, these two components retain the amplitude and phase information of the received echo. They form a complex baseband signal. Unlike simple envelope detection, this processing method preserves the phase information required for coherent signal processing.
The echo amplitude can be calculated from the I and Q components. At the same time, phase changes between successive echo pulses can be analyzed. For a moving target, the Doppler effect produces characteristic phase changes that provide information about the target's radial motion.
Subsequent signal processing uses this information, for example, for moving target indication (MTI) or processing with multiple Doppler filters, known as moving target detection (MTD). These techniques improve the separation of moving targets from echoes produced by stationary objects. Their effectiveness depends, among other factors, on coherence, pulse repetition frequency, observation time, and the interference environment.
In modern surveillance radars, received signals are frequently digitized at the intermediate-frequency stage or after I/Q demodulation. Depending on the receiver architecture, quadrature demodulation may be performed by analog circuitry or digital signal processing. The resulting data can be used to derive amplitude information, Doppler information, and other measured parameters.
The coherent channel is therefore not merely an additional output for displaying moving targets. Phase-preserving signal processing provides an essential foundation for modern radar signal processing. Final target detection takes place in subsequent processing stages, which may combine interference suppression, threshold detection, and joint analysis of multiple echo pulses.