www.radartutorial.eu www.radartutorial.eu Radar Basics

Radar Equation for Weather Radar

The radar equation presented in this section assumes familiarity with the derivation of the basic radar equation in the section “Radar Basics”. As a reminder, here is the equation expressing the received power as a function of all other factors:

Radar equationwhere

Pe = received power
Ps = transmitted power
G = antenna gain
σ = radar cross section
λ = transmitter wavelength
R = range to the reflecting object(1)

This radar equation describes a point target, that is, a target whose dimensions are much smaller than the pulse volume of the radar. Weather radar systems operate on essentially the same principle as primary surveillance radars. The main difference between the radar cross section σ of an aircraft and that of a weather phenomenon is that even a small rain cloud has far greater dimensions than the largest aircraft (although a cloud is partially transparent to radar waves). Let us examine how the radar cross section of a precipitation region is determined.

In rain, each individual raindrop is much smaller than the radar wavelength. Its radar cross section can therefore be determined using the formula for Rayleigh scattering:

Rayleigh scattering; where

D = raindrop diameter
ε = complex relative permittivity.(2)

For backscattering, the relevant quantity is the dielectric factor |K|2, which is derived from ε. In the L- through X-bands commonly used in radar, its value is approximately 0.93 for water and about 0.2 for ice. These values also depend on frequency and temperature.

However, we do not detect just one raindrop, but a certain number of them in a unit volume, in this case 1 m3.

Here, Z denotes radar reflectivity, and η is the reflectivity per unit volume.

Figure 1: Pulse volume

Figure 1: Pulse volume

If the raindrops fill the entire pulse volume of the main lobe of the antenna pattern, this volume is given by:

where


φ = vertical beamwidth of the antenna pattern
θ = horizontal beamwidth
R = range from the radar
c0 = speed of light
τ = transmitted pulse duration(4)

Recall the radar equation for point targets from the section “Radar Basics”. We replace the radar cross section in the equation with the expressions derived above:

(5)

The considerable influence of |K|2 in practice can be seen in weather radar imagery. At high altitudes, where temperatures are low, precipitation falls as snow. Dry snow has a very small radar cross section. As snowflakes descend into warmer air, they begin to melt. At first, the snow becomes wet, and its reflectivity increases dramatically.

In the warmer air layers below, only liquid water droplets remain. The radar cross section decreases again, while their fall speed increases. This produces a band of enhanced radar echoes at a particular altitude, known as the “bright band”, on the radar display.

Figure 2: Pulse volume as a function of range

Figure 2: Pulse volume as a function of range

We have now established the fundamental difference between the radar equation for surveillance radars and that for weather radars.

However, this form is not yet suitable for practical weather radar applications. Here, we are considering it not from a meteorologist's perspective, but from that of a radar technician familiar with surveillance radars. If we rearrange this equation to solve for range R, as with surveillance radars, we find that the familiar fourth root is replaced by a square root. Why?

The pulse volume increases in proportion to the square of the range! At a given particle density, it therefore contains far more reflecting raindrops at greater ranges, resulting in considerably more reflected energy than from a single point target (such as an aircraft). Whereas the maximum range of a surveillance radar depends on the fourth root of its parameters, the corresponding dependence for weather radar involves a square root!

Whereas the maximum range of a surveillance radar depends on the fourth root of its parameters, the corresponding dependence for weather radar involves a square root!

Which equation is actually used in weather radar?

Recall the basic requirement: weather radar must measure the magnitude of the echo signal. The echo signal should therefore depend on the type, size, and number of precipitation particles per unit volume. The individual radar parameters should be combined into a constant k, since they should not change during weather observations:

Radar equation for weather radarwhere
 
 

Pe = echo signal power
Ps = transmitted power
k = radar-specific factor describing the radar system
λ = transmitter wavelength
ε = here, for simplicity, the dielectric factor |K|2 of the scattering particles
N = number of precipitation/cloud particles
D = diameter of precipitation/cloud particles (6)

 

In this simplified equation, ε denotes the dielectric factor |K|2, which depends on the physical properties of the reflecting particles (precipitation or cloud particles). Its value can range from about 0.2 for ice to about 0.93 for raindrops.

The main difficulty for weather radar is that this equation contains three unknown quantities (ε, N, D). They cannot be determined unambiguously from the measured received power alone. The radar software must therefore make additional assumptions about the properties and size distribution of the precipitation particles. Mixtures of different precipitation types are also possible.

It is interesting that the raindrop diameter appears to the sixth power. This means that a single raindrop with a diameter of 5 mm reflects as much power as 15,625 raindrops with a diameter of only one millimeter (1 · 5⁶ = 15,625 · 1).