Tips and Warnings for Building Your Own Radar
Forums and blogs sometimes raise the question of what should be considered when building a radar system yourself. Adventurous designs are often mentioned involving a satellite dish and a magnetron taken from a microwave oven, but such designs have virtually no chance of functioning properly.
Building your own radar that can even be operated legally is, however, easier than one might think.
But as a general rule: Keep away from magnetrons taken from microwave ovens!
For safety reasons, it is generally advisable to limit yourself to semiconductor modules,
since their moderate operating voltages present a much lower hazard.
Frequently Asked Questions
What transmitter power is required to achieve a range of about 2 to 3 kilometres?
Two conditions determine the range of a radar. First, there is a timing condition that must ensure sufficient receiving time for the required propagation time of the electromagnetic waves. Second, there is an energy condition requiring the transmitter power budget to be large enough to compensate for the losses on the outward path, at reflection, and on the return path, so that an echo signal suitable for processing still reaches the receiver.
If you choose a pulse radar, the pulse power required for this range is, according to the radar equation, roughly 5 to a maximum of 10 W. The pulse repetition frequency should suitably be in the range from 1 to a maximum of 10 kHz, which is more than sufficient for unambiguous measurements over this distance.
If you choose an FMCW radar, a transmitter power of 10 to 30 mW is entirely sufficient. Instead of the pulse repetition frequency, the burst duration has a similar function here (that is, the duration of one measurement cycle, corresponding to the duration of the linear frequency increase). Since this is usually in the millisecond range, ambiguous range measurements are not to be expected.
The reason why an FMCW radar can achieve a greater range with less power than a pulse radar is that range is determined not simply by pulse power, but by the energy content of the transmitted pulses. Therefore, at most, the average power of the pulse radar can meaningfully be compared with the power of the FMCW radar.
Which frequencies can I use for a home-built radar?
Several frequency bands have been authorised specifically for measurement technology (and radar is a measurement technology). One particularly well-known frequency is 24.125 GHz in the K-band, for which a wide range of radar modules is already available for hobby applications. These frequency authorisations issued by the German Federal Network Agency are generally also subject to limits on maximum transmitter power.
Projects such as UWB radar are also permitted. Such systems transmit only a few extremely short pulses, which at greater distances can hardly be distinguished from natural environmental noise. Since the German Federal Network Agency cannot readily measure such additional radiation in the form of noise pulses, it cannot claim that they are causing interference somewhere. For this reason, UWB radars with limited pulse power have generally been authorised by regulation.
UWB radar is nevertheless not recommended for hobbyists with little experience in RF technology. Faster and more reliable results can be achieved with commercially available FMCW radar modules. These already contain the transmitter, receiver and antenna radiators and only need to be connected to low-frequency circuitry. But take care! Many very inexpensive modules are only suitable as CW radar and cannot be modulated. As a result, they normally cannot measure range. As a rule of thumb, if a radar module has only three connection pins, it is definitely not suitable for FMCW operation.
Can I use an old satellite dish as an antenna for the radar module?
In general: yes. Since satellite dishes are designed for frequencies of up to about 13 GHz, they are theoretically much more effective at around 24 GHz than when used in a satellite receiving system. It is only necessary to ensure that the reflector is not deformed, otherwise this gain will be lost again. Trying to give the reflector a more “radar-like” shape with an angle grinder will therefore not work.
When aligning the dish, it must also be taken into account that these antennas are actually intended to receive signals from a direction about 27°…30° above the horizon. For horizontal radar radiation, the dish therefore has to be tilted forward by approximately this angle.
An old LNB with a neck diameter of 40 mm can simply be dismantled, and a basic radar module with only two patch antennas can be mounted in the housing behind the horn radiator so that the patch antennas lie approximately in the centre of the circular waveguide section. This is not particularly efficient, because the two patch antennas have to share the centre, meaning that neither of them is positioned exactly in the middle. However, this arrangement has the advantage that the original LNB housing provides good mechanical support in exactly the correct position and also protects against splashing water.
The formal legal aspects of such a design can, however, become problematic. Even a relatively small satellite dish with a diameter of only 60 cm has an antenna gain of up to 36 dB, which corresponds to a factor of about 4000. Under certain circumstances, the combined losses may not be sufficient to ensure compliance with the maximum permissible EIRP required by the German Federal Network Agency. EIRP (Effective Isotropic Radiated Power) is the transmitter power multiplied by the antenna gain. There is a simple remedy here as well: if such a case should occur, a small piece of expanded polystyrene can be placed inside the LNB housing directly in front of the transmitting antenna group, and its slight attenuation is entirely sufficient for this purpose.
What about radiation exposure from this radar — are health effects to be expected?
The transmitter powers of commercially available radar modules are all in the range of only a few milliwatts.[1] (See technical data at http://www.viasat.com/files/assets/web/datasheets/24GHz_RADAR_chip_103_web.pdf) Even when an antenna reflector with a gain of 36 dB is used, an effective power of about 1 to a maximum of 4 W can be expected only in the main radiation direction. (In Germany, the permissible limit would be 50 W per square metre.) This calculation is, however, far removed from real conditions, because at a distance of one to two metres the radar cannot illuminate an entire square metre since the antenna pattern is much narrower.
Beyond a distance of about two metres, the losses caused by beam divergence (see: free-space path loss) again become large enough for the radiation exposure to decrease with the square of the distance. In the worst case, at a distance of one metre directly in the main beam (and in practice it is difficult to get much closer than that), this radar produces radiation exposure comparable to that of a mobile phone held directly against the ear. When standing beside the radar, that is, outside the main radiation direction, its radiation exposure can be regarded as negligible.
If you have any more questions…
…you can also send them to me by e-mail. Use the address given in the imprint.